Concrete optics and concrete living accessories are currently very trendy and modern. Everywhere there are different articles and explanations, which convince with their simple appearance. However, you can produce your own products yourself, because it is relatively easy to work with concrete and is also suitable for laymen. For example, a diy concrete lamp you tinker with little time and materials yourself. More information and tips on working with this material will soon be available.
Concrete lamp – What is concrete?
Concrete is a natural product, environmentally friendly and sustainable. It can be recycled and reused. The recipe for concrete is simple and this is what Nature gives us: a mixture of clay and limestone. Gravel and sand are also added to the gravel. Without water it is not natural. The exact mixing ratio of all ingredients plays a very important role. The properties, in particular the durability, which the cement shows. To improve these, additives are used. Thus, the concrete cures, For example, faster, becomes stronger, denser, etc. The mixing screens vary in order to adapt optimally to the given requirements. There is a wide range of concrete, depending on how hard or light, heat-insulating or pressure-resistant the concrete should be.
Diy concrete lamp and How to Mix Concrete Properly? – Mixing conditions
If concrete needs to be poured, it is advisable to mix the mixture with a little more liquid to allow it to be more easily added to the casting mold. As a result, the time for the curing also declines. For decorative purposes, such as a diy concrete lamp, where no heavy weight needs to be supported, as with a house for example, this does not play a big role. The exact mixing ratios are usually found on the back of the package. In this case, we recommend adding 10 parts of concrete mixture to a partial water. It really depends on how much the corresponding mold is actually.
Diy concrete lamp – Choose concrete or creative concrete?
If you use concrete from the hardware store, it is advisable to keep the manufacturer’s instructions. For creative work, creative concrete is preferred because it is free of pollutants and low dust. In addition, the mixture is finer and results very good results especially with smaller products – hardly bubbles, very high density. Regardless of the type of concrete you are working on, we recommend to mix the concrete before mixing. But make it outside the living area, because you should not inhale the concrete dust. For this purpose, an old noodle sieve serves to eject the coarse particles.
Diy concrete lamp – Instructions and materials
With concrete, a lot of objects can be executed and creative ideas can be realized. The slightly cold concrete look fits perfectly into any modern ambience, but works wonderfully in the traditional furnishing style. In addition, the material can be supplemented by others and can also be treated creatively after drying. Accents by color or napkin technique, installation of additional elements are feasible. Concrete greatest advantage is that it is cheap, therefore easy to access and easy to disassemble. No specific materials, tools and accessories are required to make a concrete lamp yourself. In addition, concrete is environmentally friendly and sustainable.
For the diy concrete lamp you can use different shapes. If you want to use a mold several times, choose one from plastic or from silicone. Depending on the shape and taste, some baking and muffin shapes can also be used here. There is also the possibility to order an individual form. However, any PET bottles or tetrapacks can be used, which must be disposed of afterwards. In order to be able to easily remove the concrete later, the mold is sprayed with oil before pouring. While working with concrete, we strongly recommend wearing gloves and protective masks. Concrete dust dries the house very quickly, attacks it and can cause the so-called cement firing.
Required materials and tools:
- lamp socket
- Two PET bottles for the mold – a small and a larger one
- 1 thread
- Cordless Screwdriver
- 2 – 3 screws
- Creative concrete or cement
- 1 empty can
From two PET fakes, you can make a mold yourself and develop it yourself if you are able to choose the PET bottles so that they fit together as size and shape. The larger one cut off about 1/3 of it. The covers of the two bottles are drilled in the center by means of the cordless screwdriver. Insert the small bottle into the large one and fiexiren with the thread the two in the correct position. You should remember that the distance between the two bottles will actually be the thickness of the lamp walls.
To keep the two bottles stable in the desired position, tighten 3 -4 screws. The machined thread should be at least as thick as to allow the connection cable to run loose (7 mm diameter should actually be sufficient). Now take the can, flip the bottles and place vertically into the can. This makes the mold easier to pour.
Mix the concrete in a pot under a bowl of water. You can make the mixture more liquid and gradually add it to the self-made mold. Wait a short time between the concrete layers so that no unsightly air bubbles are formed. Fill up to the screws that you have previously tightened. Allow to cure for one day. The next day, you can free the concrete lamp from the outer PET bottle to let it dry for another three days.
Remove the outer PEt bottle layer when the concrete has already hardened slightly but is not yet solid. With a cut knife you can clean the edges. The next day try to remove the smaller PET bottle from the concrete lamp interior carefully. Try first with cautious turning movements. After complete drying, treat the surface with fine-grained sandpaper and smooth it off. Finally, remove the threads and insert the socket and the connection cable. If the concrete lamp is damaged in some places, it is possible to repair the mold afterwards. For this, mix a little cement with water and fill the empty areas with a small spatula or chopsticks.
Prefabricated concrete from the construction market has a slightly more beautiful look compared to the creative concrete. The first serves as a building element, forms larger holes and therefore does not have a decorative effect. On the other hand, creative concrete dries evenly, is fine-pored, and in the rarest cases small breaks are formed at edges. In addition, the concrete look has a slightly porous appearance.
There are several variants of how you can design your concrete product in various ways or in color. Concrete can still sound in the liquid state. Acrylic or chalk paints are used for this purpose. Subsequently, after the concrete lamp is already finished, one can paint with brush paint. With the aid of adhesive tape geometrical figures or simple lines can be painted and then painted. Another option would be to use the napkin technique and to make a motif with a napkin glue.
Home accessories: DIY concrete lamp
The second variant for diy concrete lamp is to use a mold or a milk pack. The lamp holder and textile cable are fastened in the pack and the cast concrete is already filled. The next day the pack can be removed and the lamp should be dried for another three days.
If it is a table lamp like this, then you only need a nice light bulb. Here is a vintage look, which is very interesting and striking. This is simply screwed and placed on a side table for decoration. As a holder for the light bulb, take a perfectly normal socket with cable. You can choose a striking model with a colorful textile cable. On one side you should also make a hole for the cable. Please use a suitable drilling tool.
If the frame does not fit perfectly and wiggles back and forth, take for example matches and something else, and press evenly to close the gap. On the lower side it is advisable to apply a few self-adhesive rubber buffers so that the furniture of the rough concrete is not scratched or damaged.